Skip to main content

Full text of "Hacks and Mods"

See other formats


Temperature Logger Modification 



i 



Make Projects 



build, hack, tweak, share, discover, J 



Temperature Logger 



Modification 



Written By: Andrew Townsend 



f TOOLS: 



Software from 3M website (1) 

Soldering iron and solder (1) 

Very small phillips screwdriver (jewelry 
size) (1) 

Windows computer (1) 



© PARTS: 

• 3M TL20 temperature loggers (Box of 5) 

• 3M TL20 temp, logger USB cable (1) 
(mini USB for the TL30) 

• 2-wire cable (1) 
(high temperature) 



SUMMARY 

For many years I have been searching for temperature-recording equipment. There were a 
lot of types available, such as old paper chart recorders. For computers there are various 
types, some expensive, single-channel, DIY units requiring programming, ADC (Analog to 
Digital Converters) with poor voltage sensitivity at thermocouple levels, and requiring a 
power supply to take records. 

I came across the 3M temperature logger while looking through an office stationery supplies 
catalog. They are usually packed with heat-sensitive goods in a parcel for posting. 

The temperature logger records the temperature at user-set intervals. The parcel's recipient 



© Make Projects 



www.makeprojects.com 



Page 1 of 4 



Temperature Logger Modification 

can download the recorded log with a special USB cable. 

The temperature loggers come in boxes of five, and require the special USB cable which 
comes in a bag of two. (The newer TL30 uses a miniUSB socket). The loggers contain a 
battery. 

One limitation of the TL20 temperature loggers is their +60°C (140°F) maximum 
temperature. This is a limitation of the case and battery. The sensor can measure far higher 
-- up to around 140 °C. 

The logger's features make it practical to measure temperatures in factory situations and 
school laboratory experiments. Each logger will record up to 30 minutes. 

I also used an electric roast-temperature probe that was supplied with a microwave oven. It 
is designed for +200°C (392° F) with silicone-covered cable. The thermistor inside has a 
different resistance and reads an estimated +38 °C under actual. 

To make measurements in liquids such as water, the sensor will need covering. The logger 
case can be located safely away from what is being measured. 

Note: Leaving the logger plugged into the USB cable will drain its battery. 

Having 5 loggers allows simultaneous measurement of ambient temperature and 4 more 
areas . 

On a machine such as a 3-way absorption refrigerator, you can use one inside the freezer, 
one on the middle radiator, one on the top radiator, and the most heatproof on the generator 
element. Place them carefully so as not to damage the machine. 

A whole range of effects can be measured, such as: 

Insulation lossesMaximum hot/cold, etc. Temp vs. time factor, when heating freshwater ice, showing temperature 
increase is not linear (at the change-of-state points)ls coffee hotter when milk is poured in first? Or did the boiling water 
cool quicker when poured into a cold china mug?The enthalpy of evaporation. 



© Make Projects www.makeprojects.com Page 2 of 4 



Temperature Logger Modification 











i "3 r : V 1 




ISS3E3J 






,,-*,-* . 






i * 


O 
^ 




F.JPG 





Peel off the back sticker. (D.JPG, E.JPG) 
Unscrew and remove the back cover. (F.JPG) 





H.JPG 





• Then the five screws holding the circuit board. (G.JPG) 

• In picture H.JPG the screwdriver is pointing to the thermistor, colored blue, which I 
desoldered from the circuit board, then resoldered at the end of a cable. Then I soldered 
the cable to the circuit board. 



© Make Projects 



www.makeprojects.com 



Page 3 of 4 



Temperature Logger Modification 




• Cut the sensor vent hole in the case for the sensor cable to pass through. 

• Replace the circuit board and screws. At this stage I tested the logger buttons and 
connected it to the computer, to check that the temperature is being recorded. I had 
trouble with the Start/stop button, so I disassembled it and cleaned the contacts. 

• Replace the back cover and screws. 

• Use sleeving and silicone RTV to protect the thermistor. 

This document was last generated on 201 2-1 1 -03 1 2:58:1 5 AM. 



© Make Projects 



www.makeprojects.com 



Page 4 of 4